The Samsung Dishwasher Error Code 9E Indicates to the Low water level error. It means that the float sensor is signaling that there is not enough water for washing the dishes. It will send a signal to the control panel, which will activate the self-diagnosis system, and you will get the 9E error in the display panel.
If this error problem occurs for the first time, you need to reboot your control module by disconnecting the control unit from the main switch for about 10 minutes. If in case your Samsung dishwasher is in the manual mode, and then some of the dishwasher available in the market allows you to reset the manual setting of error code 9E. You can reset the setup by pressing the power button, then the screen will display the menu, which will appear on the panel on the upper left corner. You can also do the following steps:
- Empty the Samsung dishwasher.
- Add the detergent.
- Start the dishwasher, and run it with normal wash cycle.
How To Solve Samsung Dishwasher Error Code 9E
For solving the 9e error, we must first identify the source of the problem and then diagnose it.
Reasons for 9E problem
There are so many reasons that can cause the error problem 9E in the Samsung dishwasher. It is important to keep in mind that while using your dishwasher to stand steadily and check if the inlet hose is neither pinched nor twisted, check if the inlet valve is working properly. You still not find any problem then the root cause of this error may be in the electronic components of your Samsung dishwasher. But still, this error can also be caused by some other factors.
Check the Float Sensor
The float, which is in plastic, is in the white box, which lies in Steel’s panel and is located on the left side of the bottom. The sensor in the float is the main reason the 9E error code occurs in your Samsung dishwasher. The sensor helps you by indicating when the level of water rises, and it pops up and gets pressed on the lever, and all the activities are brought back to the microswitch. But still, you may face some other error, such as the lever getting stuck and is not able to respond to the pressing. You may also face problems with the sensor being covered with Slime and getting stick to the wall. Also the debris that has been accumulated does not allow the parts of the dishwasher to move properly. To check the right position of the sensor switch, then you need to follow the following steps:
- First of all, press the buttons of our Power, Normal, and the delay one by one.
- Then you need to wait for some time for the instruction of T1, which is the test number one to check the sensor’s function when the level of water is low.
- Then start the drain pump again, and you can do it by pressing the Delay Start button.
- After that, you need to press the NORMAL button for about four times when the indicator of the Pulse Count displays that the count has reached above 660.
- You need to wait for at least 30 seconds when the test number t5 is stopped, and this is the time when the water is drained out of your Samsung dishwasher.
- Now press the NORMAL button. You will see the t6 and OFF message on the display screen.
Check the Wiring Connection
The 9E error code can be due to the damage in the wire. You need to check the wiring between the sensor and the control module. The reason behind this loose connection is because of the damaged wire, or even the short circuit has occurred in the electronic components of your Samsung dishwasher. So to avoid this Samsung Dishwasher Error Code 9E, you need to check the electrical circuit by checking the wiring harness. Check any problem between the brown wire, which indicates the low level of water and the connecting points which connect directly to the circuit board and solder or squeeze out that area. In case if you still are facing this problem, then you need to change the wiring.
Faulty Sensor
The 9E error code in your Samsung dishwasher may point to the broken float sensor. Its mechanical parts maybe not working and are broken. And if you are planning to buy the sensor, then both the type of sensor will cost you $60. It will help you in avoiding the 9E error code in your Samsung dishwasher.
Control Board is Broken
If you find no error in the sensor and the wiring, then you must check the PBA mainboard and check for any faults in it. This 9e error can also be due to the breakdown in the surge of power. You can restore the burnt parts and the wires that are damaged and prevent your Samsung dishwasher, causing an error called the 9E error code. But if the microcircuit is broken, then it cannot be repaired, and then you need to replace all the subunits to avoid this problem.
How to fix the 9E error problem
- To eliminate this problem permanently, you need to, first of all, remove the sensor and washer also and adequately clean the chamber’s wall. If you find that the lever is stuck, you can simply press on its several times to make it work.
- You need to make sure that your dishwasher is not leaking from anywhere, and you can work on it according to the user manual guide that comes with the product.
- If in case you have moved your dishwasher from one place to another, then it might be possible that some amount of water has been splashed out, then you need to wait for some time to let it dry.
We hope that we have now solved the Samsung Dishwasher Error Code 9E. We have also given the solution for Error Code 7E on our website. Please check it out as well.